TOGGLE BOLT AND WING


TOGGLE BOLT AND WING ANCHORS
Toggle wings are light-duty anchors for use in hollow base material applications. They spread the load over a large area and are more temperature resistant than other hollow anchors. They are single-use anchors.

Material: AISI 1008 or equivalent cold rolled steel
PLASTIC ANCHOR
PLASTIC ANCHORS
Plastic anchors are a more economical, light-duty part than steel hollow wall anchors. They can be used in sheetrock, plaster, brick, concrete or tile. The design of the collar allows plastic anchors to also be used in hollow material. For use with self-tapping or wood screws.

Material: Polyvinylchloride or Polyethylene plastic
 
DROP-IN ANCHOR
DROP-IN ANCHORS
Intended for flush mounted, medium to heavy-duty applications in solid material such as stone and concrete. It can be used in, but are not limited to, overhead assenblies such as duct work and pipe hangers because the internal plug holds its position. Can also be used to anchor handrails and floor-mounted stops.

Material:
Anchor Body: AISI 12L14 cold rolled steel
Expander Plug: AISI 12L14/1215 cold rolled steel, case-hardened and tempered
 
EXPANSION SHIELD ANCHOR




EXPANSION SHIELD ANCHORS
Used in soft masonry with machine screws or machine bolts which are exposed to vibration or side pressure. Can also be used in harder materials, including stone, brick, concrete or block

Material: Expansion shield and not may be made of alloy zinc, brass, malleable iron or steel.
HOLLOW WALL ANCHOR
HOLLOW WALL ANCHORS
Steel hollow wall anchors are considered to be light-duty anchors. They require a pre-drilled hole and may be used in drywall, sheetrock, plaster or paneling. When properly installed, they will not crack or crumble the wall material and reist vibration. The machine screw may be removed and inserted multiple times to accomodate an exchange of fixtures.

Material:
Shell: AISI C1008 - 1010  or equivalent cold-rolled steel
Screw: AISI C1010 - 1018  or equivalent cold-rolled steel
LAG SHIELD
(LEAD ANCHOR)
LAG SHIELD (LEAD ANCHORS)
Lag shields are medium-duty anchors which expand to fill the area of the pre-drilled hole when a lag screw is tightened into the shield. Extra-long sizes are for use in mortar or brick. Standard lengths are intended for use in concrete. They can be used in solid or hollow material and are more resistant to temperature fluctuations and rust than other light-duty anchors.

Material: Die-cast zinc
PLASTIC TOGGLE
PLASTIC TOGGLE ANCHORS
When a tapping screw is driven into the toggle, the legs collapse which form a tongue. As the screw is driven through the body, it pulls in and expands the legs. Plastic toggles are intended for lightweight duty in hollow walls (wallboard or plaster). The anchor remains in place even after the screw is removed.

Material: High strength nylon
WEDGE ANCHOR
WEDGE ANCHORS
These are heavy-duty, non-bottom bearing anchors of greater shear strength than other light and medium-duty expansion anchors. The design of the expansion clip assures full contact with the masonry. Wedge anchors withstand temperatures fluctuations well. For best performance, minimum anchor spacing should be 10 hole diameters and minimum edge distance be 5 hole diameters.

Material:
Anchor Bolt: AISI 1215-12L14 or equivalent free-machine carbon steel
Clip: AISI C1010-1018 or equivalent  carbon steel
Nut: ASTM A-563 Grade-A carbon steel
Washer: AISI C1010-1018 or equivalent carbon steel
MACHINE SCREW ANCHOR
MACHINE SCREW ANCHORS
A caulking type anchor which provides a quick setting in brick, concrete or stone. The lead shield's maleability enable it to fill uneven or irregular spots in the hole. When tamped, the expansion sleeve holds the expander inside the hole in the masonry, equally distributing the load around the anchor. Fixtures can be removed without sacrificing holding power.

Material:
Cone: May be one of the following materials: Brass, Malleable Iron, Steel or Die Cast Zinc Alloy
Expander Shield: Lead or 3-5% Antimonial Lead Alloy
L-ANCHOR
L-ANCHORS
L-Anchors are preset into concrete. After curing, the threaded portion stands out from the concrete and is used to fasten down machinery, equipment, etc.

Material:
Steel - Stainless - other Alloys
* If you do not see your requirement list. Please contact us!
  
Washers
Sheet Metal
Nuts
Machine Screws
Self Drilling