HEX HEAD CAP SCREW

HEX HEAD TAP BOLTS

HEX HEAD CAP SCREW

• Grade – 2 – 5 - 8
• Material – Plain – Zinc – Zinc Yellow – Stainless Steel
• Diameter – ¼" and up
• Length – 3/8" and up
• Thread Pitch – Coarse – Fine
• Also Available in Metric

CARRIAGE BOLTS ROUND HEAD, SQUARE NECK

CARRIAGE BOLTS

• Grade – 2 – 5
• Material – Plain – Zinc – Stainless Steel
• Diameter – 3/16" and up
• Length – ½" and up
• Thread Pitch – Coarse – Fine
• Also Available in Metric

STRUCTURAL BOLTS

STRUCTURAL BOLTS

• Material – Plain – Hot Dipped Galvanized
• Diameter – ½" and up
• Length – 1 ¼" and up
• Thread Pitch – Coarse

HEX HEAD LAG SCREW

HEX LAG BOLTS

• Material – Plain – Zinc
• Diameter – ¼" and up
• Length – 1" and up

HEX FINISHED NUTS

FINISHED HEX NUTS

• Grade – 2 – 5 – 8
• Material – Plain – Zinc – Zinc Yellow – Stainless Steel – Brass
• Diameter – ¼" and up
• Thread Pitch – Coarse – Fine
• Also Available in Metric

HEAVY HEX NUTS

HEAVY HEX NUTS

• Grade – 2 – 2H
• Material – Plain – Zinc - Zinc Yellow –Stainless Steel – Hot Dip Galvanized – Brass
• Diameter – ¼" and up
• Thread Pitch – Coarse – Fine

HEX JAM NUTS

HEX JAM NUTS & HEAVY HEX JAM NUTS

• Grade – 2
• Material – Plain – Zinc – Zinc Yellow – Stainless Steel – Brass
• Diameter – ¼" and up
• Thread Pitch – Coarse – Fine
• Also Available in Metric

HEX MACHINE SCREW NUTS

HEX MACHINE SCREW NUTS & SMALL PATTERN NUTS

• Grade – 2
• Material – Plain –Zinc – Stainless Steel – Brass – Nylon
• Diameter - #2 and up
• Thread Pitch – Coarse- Fine

REGULAR SQUARE NUTS

SQUARE MACHINE SCREW NUTS

SQUARE NUTS – REGULAR & MACHINE SCREW

• Grade – 2
• Material – Plain – Zinc – Stainless Steel – Hot Dipped Galvanized
• Diameter - #6 and up
• Thread Pitch – Coarse – Fine

HEX NYLON INSERT LOCK NUTS

NYLON INSERT LOCK NUT

• Styles – Regular – Thin Height – Heavy Pattern
• Grade – 2 – 8
• Material – Plain – Zinc – Zinc Yellow – Stainless Steel – Brass
• Diameter - #4 and up
• Thread Pitch – Coarse – Fine

HEX COUPLING NUTS

HEX COUPLING NUTS

• Grade – 2
• Material – Plain – Zinc – Stainless Steel
• Diameter – ¼" and up
• Thread Pitch – Coarse – Fine
• Also Available in Metric

WING NUTS COLD FORMED STEEL

WING NUTS STAMPED STEEL

WING NUTS

• Styles – Forged – Stamped
• Grade – 2
• Material – Plain –Zinc – Stainless Steel – Brass
• Diameter - #6 and up
• Thread Pitch – Coarse – Fine
• Also Available in Metric

HEX FLANGE NUTS

FLANGED NUTS

• Styles – Non-serrated – Serrated
• Grade – 2
• Material – Plain – Zinc – Stainless Steel
• Diameter - #6 and up
• Thread Pitch – Coarse – Fine

HEX ACORN CAP NUTS

ACORN NUTS

• Material – Nickel – Brass – Stainless Steel
• Diameter - #6 and up
• Thread Pitch – Coarse – Fine
• Also Available in Metric

STRUCTURAL NUTS

STRUCTURAL NUTS

• Material – Plain – Hot Dipped Galvanized
• Diameter – ½" and up
• Thread Pitch – Coarse

FLAT WASHERS SAE, STEEL

FLAT WASHERS USS, STEEL

FLAT WASHERS "FENDER", STEEL

FLAT WASHERS

• Styles – USS – SAE – Fender
• Material – Plain – Zinc – Zinc Yellow – Stainless Steel
• Diameter – #2 and up
• Also Available in Metric

REGULAR LOCK WASHERS

HEAVY LOCK WASHERS

LOCK WASHERS

• Styles – Medium & Heavy Split
• Material – Plain – Zinc – Stainless Steel
• Diameter – #2 and up
• Also Available in Metric

TOOTH LOCK WASHERS INTERNAL TOOTH

TOOTH LOCK WASHERS EXTERNAL TOOTH

TOOTH LOCK WASHERS INTERNAL-EXTERNAL TOOTH

TOOTH LOCK WASHERS COUNTERSUNK

TOOTH LOCK WASHERS

• Styles – Internal – External – Internal/External – External Countersunk
• Materials – Plain – Zinc – Zinc Yellow – Stainless Steel
• Diameter – #2 and up
• Also Available in Metric

STRUCTURAL FLAT WASHERS

STRUCTURAL FLAT WASHERS

• Material – Plain – Zinc – Stainless Steel – Hot Dipped Galvanized
• Diameter – 1/2" and up
• (Type F436 for an A325 Bolt)

MACHINE SCREWS PAN HEAD

PAN HEAD MACHINE SCREW

• Material – Zinc – Stainless Steel – Brass
• Diameter - #2 and up
• Length – 1/8" and up
• Thread Pitch – Coarse – Fine
• Also Available in Metric

MACHINE SCREWS ROUND HEAD

ROUND HEAD MACHINE SCREW

• Material – Zinc – Stainless Steel – Brass
• Diameter - #2 and up
• Length – 1/8" and up
• Thread Pitch – Coarse – Fine

BINDER

BINDER HEAD MACHINE SCREW

• Material – Zinc – Stainless Steel – Brass
• Diameter - #2 and up
• Length – 1/8" and up
• Thread Pitch – Coarse – Fine

FILLISTER

FILLISTER HEAD MACHINE SCREW

• Material – Zinc – Stainless Steel – Brass
• Diameter - #2 and up
• Length – 1/8" and up
• Thread Pitch – Coarse- Fine

MACHINE SCREWS TRUSS HEAD

TRUSS HEAD MACHINE SCREW

• Material – Zinc – Stainless Steel – Brass
• Diameter - #2 and up
• Length – 1/8" and up
• Thread Pitch – Coarse – Fine

MACHINE SCREWS OVAL HEAD

OVAL HEAD MACHINE SCREW

• Material – Zinc – Stainless Steel – Brass
• Diameter - #2 and up
• Length – 1/8" and up
• Thread Pitch – Coarse – Fine

MACHINE SCREWS FLAT HEAD

FLAT HEAD MACHINE SCREW

• Material – Zinc – Stainless Steel – Brass
• Diameter - #2 and up
• Length – 1/8" and up
• Thread Pitch – Coarse – Fine
• Also Available in Metric

HEX INDENTED

HEX WASHER

INDENTED HEX AND HEX WASHER MACHINE SCREW

• Material – Zinc – Stainless Steel – Brass
• Diameter - #2 and up
• Length – 1/8" and up
• Thread Pitch – Coarse – Fine

THUMB SCREWS NO SHOULDER

THUMB SCREWS WITH SHOULDER

THUMB SCREW MACHINE SCREW

• Styles – Shoulder – No Shoulder
• Material – Zinc – Stainless Steel – Brass
• Diameter - #6 and up
• Length – ½" and up
• Thread Pitch – Coarse – Fine

SHEET METAL SCREWS FLAT HEAD

FLAT HEAD SHEET METAL SCREWS

• Material – Zinc – Stainless Steel
• Diameter - #2 and up
• Length – ¼" and up

SHEET METAL SCREWS PAN HEAD

PAN HEAD SHEET METAL SCREWS

• Material – Zinc – Stainless Steel – Brass
• Diameter - #2 and up
• Length ¼" and up

SHEET METAL SCREWS TRUSS HEAD

TRUSS HEAD SHEET METAL SCREWS

• Material – Zinc – Stainless Steel – Brass
• Diameter - #2 and up
• Length – ¼" and up

SHEET METAL SCREWS OVAL HEAD

OVAL HEAD SHEET METAL SCREWS

• Material – Zinc – Stainless Steel - Brass
• Diameter - #2 and up
• Length – ¼" and up

SHEET METAL SCREWS HEX INDENTED HEAD

INDENTED HEX HEAD SHEET METAL SCREW

• Material – Zinc – Stainless Steel - Brass
• Diameter - #2 and up
• Length – ¼" and up

SHEET METAL SCREWS INDENTED HEX WASHER

INDENTED HEX WASHER HEAD SHEET METAL SCREW

• Material – Zinc – Stainless Steel - Brass
• Diameter - #2 and up
• Length – ¼" and up

SHEET METAL SCREWS U-DRIVE

U-DRIVE SHEET METAL SCREWS

• Material – Zinc – Stainless Steel - Brass
• Diameter - #2 and up
• Length – 1/8" to ¾"

DRYWALL SCREWS FLAT BUGLE HEAD

BUGLE DRYWALL SCREWS

• Material – Plain –Zinc – Hot Dipped Galvanized – Black
• Diameter - #6 - #7 - #8 - #10
• Length – 1" and up
• Thread Pitch – Regular – Deep Thread – Hi(Coarse) – Hi/Lo – (Coarse & Fine) – Twin Fast

SELF-DRILLING SCREWS PAN HEAD

PAN HEAD SELF-DRILLING SCREW

• Material – Zinc – Stainless Steel
• Diameter - #4 and up
• Length – 1/4" and up

SELF-DRILLING SCREWS FLAT HEAD

FLAT HEAD SELF-DRILLING SCREW

• Material – Zinc – Stainless Steel
• Diameter - #4 and up
• Length – 1/4" and up

SELF-DRILLING SCREWS HEX INDENTED WASHER HEAD

INDENTED HEX WASHER HEAD SELF-DRILLING SCREW

• Material – Zinc – Stainless Steel
• Diameter - #4 and up
• Length – 1/4" and up

SELF-DRILLING SCREWS WAFER HEAD

WAFER HEAD SELF-DRILLING SCREW

• Material – Zinc – Stainless Steel
• Diameter - #4 and up
• Length – 1/4" and up

SELF-DRILLING SCREWS TRUSS HEAD

TRUSS HEAD SELF-DRILLING SCREW

• Material – Zinc – Stainless Steel
• Diameter - #4 and up
• Length – 1/4" and up

SELF-DRILLING SCREWS ROUND HEAD

ROUND HEAD SELF-DRILLING SCREW

• Material – Zinc – Stainless Steel
• Diameter - #4 and up
• Length – 1/4" and up

SELF-DRILLING SCREWS BUGLE HEAD

BUGLE HEAD SELF-DRILLING SCREW

• Material – Zinc – Stainless Steel
• Diameter - #4 and up
• Length – 1/4" and up

FLAT HEAD WOOD SCREWS

FLAT HEAD WOOD SCREWS

• Material - Plain - Zinc - Stainless Steel - Brass - Black
• Diameter #2 and up
• Diameter #2 and up

ROUND HEAD WOOD SCREWS

ROUND HEAD WOOD SCREWS

• Material - Plain - Zinc - Stainless Steel - Brass - Black
• Diameter #2 and up
• Length - 1/4" and up

OVAL HEAD WOOD SCREWS

OVAL HEAD WOOD SCREWS

• Material - Plain - Zinc - Stainless Steel - Brass - Black
• Diameter #4 and up
• Length - 1/4" and up

TRUSS HEAD WOOD SCREWS

TRUSS HEAD WOOD SCREWS

• Material - Plain - Zinc - Stainless Steel - Brass - Black
• Diameter #2 and up
• Length - 1/4" and up

BUGLE HEAD WOOD SCREWS

• Material - Plain - Zinc - Stainless Steel - Brass - Black
• Diameter #2 and up
• Length - 1/4" and up

TRIMMED HEAD WOOD SCREWS

• Material - Plain - Zinc - Stainless Steel - Brass - Black
• Diameter #2 and up
• Length - 1/4" and up

Specialty Wood Working Screws

MODIFIED TRUSS HEAD WOOD SCREWS

• Material - Plain - Zinc - Stainless Steel - Brass - Black
• Diameter #2 and up
• Length - 1/4" and up

Specialty Wood Working Screws

FLAT HEAD W/NIBBS WOOD SCREWS

• Material - Plain - Zinc - Stainless Steel - Brass - Black
• Diameter #2 and up
• Length - 1/4" and up

FLAT HEAD THREAD CUTTING SCREW

FLAT HEAD THREAD CUTTING SCREW

• Material - Zinc - Stainless Steel
• Diameter - #4 and Up
• Length 1/4" and Up
• Thread Pitch - Course - Fine

PAN HEAD THREAD CUTTING SCREW

PAN HEAD THREAD CUTTING SCREW

• Material - Zinc - Stainless Steel
• Diameter - #4 and Up
• Length 1/4" and Up
• Thread Pitch - Course - Fine

INDENTED HEX WASHER THREAD CUTTING SCREW

INDENTED HEX WASHER THREAD CUTTING SCREW

• Material - Zinc - Stainless Steel
• Diameter - #4 and Up
• Length 1/4" and Up
• Thread Pitch - Course - Fine

TRUSS HEAD THREAD CUTTING SCREW

TRUSS HEAD THREAD CUTTING SCREW

• Material - Zinc - Stainless Steel
• Diameter - #4 and Up
• Length 1/4" and Up
• Thread Pitch - Course - Fine

TORX FLAT THREAD CUTTING SCREW

TORX FLAT (FLOOR BOARD) THREAD CUTTING SCREW

• Material - Zinc - Stainless Steel
• Diameter - #4 and Up
• Length 1/4" and Up
• Thread Pitch - Course - Fine

CLEVIS PINS

CLEVIS PINS

• Material - Plain - Zinc - Stainless Steel
• Diameter - 3/16" and Up
• Length - 1/2" and Up

UNIVERSAL CLEVIS PINS

UNIVERSAL CLEVIS PINS

• Material - Plain - Zinc - Stainless Steel
• Diameter - 3/16" and Up
• Length - 1" and Up

COTTER PINS

COTTER PINS

• Material - Plain - Zinc - Stainless Steel
• Diameter - 1/32" and Up
• Length - 1/2" and Up

HAIR PIN COTTER

HAIR PIN COTTER (HITCH PIN)

• Material - Plain - Zinc - Stainless Steel
• Diameter - 1/32" and Up
• Length - 17/16" and Up

DOWEL PIN

DOWEL PIN

• Material - Plain - Zinc - Stainless Steel
• Diameter - 1/16" and Up
• Length - 3/16" and Up

ROLL PINS

ROLL PIN (SPRING PIN)

• Material - Plain - Zinc - Stainless Steel
• Diameter - 1/16" and Up
• Length - 3/16" and Up

TAPER PINS

TAPER PINS

• Material - Plain - Zinc
• Diameter - 1" and Up
• Length - 5/8" and Up

EXTERNAL

INTERNAL

RETAINING RINGS

External: A ring-shaped stamping with one opening on the circumference. The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shafts.

Internal: A ring-shaped stamping with one opening on the circumference. The two ends at the opening are called lugs and flare slightly into the groove. When the lugs are released, contact is made with the grooved housing.

Material:
Steel: Carbon spring steel SAE 1060-1090
Stainless: Precipitation Hardened Alloy 15% Chromium, 7% Nickel, 2% Molybdenum

E-RINGS

E-RINGS

A semi-circulr stamping with two ends which are set further apart than both internal and external rings. The two ends have flared "prongs" which are substantially wider than the other parts of the ring. A center prong extends from the inside perimeter of the ring, halfway between the two ends. The three prongs, when radially installed, make contact with the bottom of the groove.

Material:
Steel: Carbon spring steel SAE 1060-1090
Stainless: Precipitation Hardened Alloy 15% Chromium, 7% Nickel, 2% Molybdenum

O-RINGS

BUNA-O-RINGS

Buna-N-Viton-Other Material Standard & Specialty Sizes Available

SOCKET HEAD CAP SCREWS

SOCKET HEAD CAP SCREWS

• Material - Plain - Stainless Steel
• Diameter - #2 and Up
• Length - 1/8" and Up
• Thread Pitch - Coarse - Fine
• ALSO AVAILABLE IN METRIC

SOCKET BUTTON CAP SCREWS

SOCKET BUTTON CAP SCREWS

• Material - Plain - Stainless Steel
• Diameter - #2 and Up
• Length - 1/8" and Up
• Thread Pitch - Coarse - Fine
• ALSO AVAILABLE IN METRIC

SOCKET FLAT CAP SCREWS

SOCKET FLAT CAP SCREWS

• Material - Plain - Stainless Steel
• Diameter - #2 and Up
• Length - 1/8" and Up
• Thread Pitch - Coarse - Fine
• ALSO AVAILABLE IN METRIC

SOCKET LO HEAD CAP SCREWS

SOCKET LO HEAD CAP SCREWS

• Material - Plain - Stainless Steel
• Diameter - #2 and Up
• Length - 1/8" and Up
• Thread Pitch - Coarse - Fine

SOCKET SET SCREWS

SOCKET SET SCREWS

• Point Styles - Cup - Oval - Flat - Cone - 1/2 Dog - Full
• Dog - Knurled
• Material - Plain - Stainless Steel
• Diameter - #2 and Up
• Length - 1/8" and Up
• Thread Pitch - Coarse - Fine
• ALSO AVAILABLE IN METRIC

SOCKET SHOULDER SCREWS

SOCKET SHOULDER SCREWS

• Material - Plain - Stainless Steel
• Shoulder Diameter-Thread Diameter-Pitch:
  • 1/4" = #10-24
  • 5/16" = 1/4-20
  • 3/8" = 5/16-18
  • 1/2" = 3/8-16
  • 5/8" = 1/2-13
  • 3/4" = 5/8-11
• Shoulder Length - 3/8" and Up
• Also available in Metric

Available in Large Flange and Countersunk.
Call for sizes and information

• Alum / Alum
• Alum / Steel
• Steel / Steel
• Stainless / Stainless

TOGGLE BOLT AND WING

TOGGLE BOLT AND WING ANCHORS

Toggle wings are light-duty anchors for use in hollow base material applications. They spread the load over a large area and are more temperature resistant than other hollow anchors. They are single-use anchors.

Material: AISI 1008 or equivalent cold rolled steel

PLASTIC ANCHOR

PLASTIC ANCHOR

Plastic anchors are a more economical, light-duty part than steel hollow wall anchors. They can be used in sheetrock, plaster, brick, concrete or tile. The design of the collar allows plastic anchors to also be used in hollow material. For use with self-tapping or wood screws.

Material: Polyvinylchloride or Polyethylene plastic

DROP-IN ANCHOR

DROP-IN ANCHORS

Intended for flush mounted, medium to heavy-duty applications in solid material such as stone and concrete. It can be used in, but are not limited to, overhead assenblies such as duct work and pipe hangers because the internal plug holds its position. Can also be used to anchor handrails and floor-mounted stops.

Material:
Anchor Body: AISI 12L14 cold rolled steel Expander Plug: AISI 12L14/1215 cold rolled steel, case-hardened and tempered

EXPANSION SHIELD ANCHOR

EXPANSION SHIELD ANCHORS

Used in soft masonry with machine screws or machine bolts which are exposed to vibration or side pressure. Can also be used in harder materials, including stone, brick, concrete or block

Material: Expansion shield and not may be made of alloy zinc, brass, malleable iron or steel.

HOLLOW WALL ANCHORS

HOLLOW WALL ANCHORS

Steel hollow wall anchors are considered to be light-duty anchors. They require a pre-drilled hole and may be used in drywall, sheetrock, plaster or paneling. When properly installed, they will not crack or crumble the wall material and reist vibration. The machine screw may be removed and inserted multiple times to accomodate an exchange of fixtures.

Material:
Shell: AISI C1008 - 1010 or equivalent cold-rolled steel
Screw: AISI C1010 - 1018 or equivalent cold-rolled steel

LAG SHIELD (LEAD ANCHOR)

LAG SHIELD (LEAD ANCHORS)

Lag shields are medium-duty anchors which expand to fill the area of the pre-drilled hole when a lag screw is tightened into the shield. Extra-long sizes are for use in mortar or brick. Standard lengths are intended for use in concrete. They can be used in solid or hollow material and are more resistant to temperature fluctuations and rust than other light-duty anchors.

Material: Die-cast zinc

PLASTIC TOGGLE

PLASTIC TOGGLE ANCHORS

When a tapping screw is driven into the toggle, the legs collapse which form a tongue. As the screw is driven through the body, it pulls in and expands the legs. Plastic toggles are intended for lightweight duty in hollow walls (wallboard or plaster). The anchor remains in place even after the screw is removed.

Material: High strength nylon

WEDGE ANCHORS

WEDGE ANCHORS

These are heavy-duty, non-bottom bearing anchors of greater shear strength than other light and medium-duty expansion anchors. The design of the expansion clip assures full contact with the masonry. Wedge anchors withstand temperatures fluctuations well. For best performance, minimum anchor spacing should be 10 hole diameters and minimum edge distance be 5 hole diameters.

Material:
Anchor Bolt: AISI 1215-12L14 or equivalent free-machine carbon steel
Clip: AISI C1010-1018 or equivalent carbon steel
Nut: ASTM A-563 Grade-A carbon steel
Washer: AISI C1010-1018 or equivalent carbon steel

MACHINE SCREW ANCHORS

MACHINE SCREW ANCHORS

A caulking type anchor which provides a quick setting in brick, concrete or stone. The lead shield's maleability enable it to fill uneven or irregular spots in the hole. When tamped, the expansion sleeve holds the expander inside the hole in the masonry, equally distributing the load around the anchor. Fixtures can be removed without sacrificing holding power.

Material:
Cone: May be one of the following materials: Brass, Malleable Iron, Steel or Die Cast Zinc Alloy Expander Shield: Lead or 3-5% Antimonial Lead Alloy

L-ANCHORS

L-ANCHORS

L-Anchors are preset into concrete. After curing, the threaded portion stands out from the concrete and is used to fasten down machinery, equipment, etc.

Material:
Steel - Stainless - other Alloys

PHILLIPS INSERT BIT

Phillips is the most popular style in the industry. The reduced diameter variety is recommended for installing drywall or particle board screws. Power bits are used with power driven tools. Insert bits are ideal for hand drivers, or may be used in conjunction with bit holders in power drivers. Extra hard bits are used specifically with case hardened screws.

Material: Chrome vanadiun tool steel

SLOTTED INSERT BITS

Slotted bits require less downward pressure to drive parts than those with cross-recessed openings. It is important to choose the proper fitting blade to minimize slippage.

Material: Chrome vanadium tool steel

TORX INSERT BITS

Torx-Equivalent bits offer a positive-engaging, fast-locating method of transmitting torque and optimizing worher efficiency. The positive torque control adds to the bit's drive life.

Material:Chrome vanadium tool steel

POZIDRIV INSERT BITS

Pozidriv-equivalent bits have an eight-bar pattern as opposed to Phillips bits which have a four-bar pattern. The extra bars provide greater torque with less cam-out. They are for use with Pozidriv-Equivalent screws.

Material: Chrome vanadium tool steel

SQUARE DRIVE INSERT BITS

Square recess bits are popular in the furniture, mobile home and recreational vechicle industries. They are used in many overhead installations. They increase productivity with torque transmission and resist cam-out.

Material:Chrome vanadium tool steel

POWER BITS

Power Bits are available in all drive styles

MAGNETIC POWER NUTSETTERS

Nutsetters are used to drive hex head tapping screws and machine screws. They are magnetic to provide excellent tool-to-fastener holding power. They are popular in prefabricated home and metal building construction.

Material: 50BV30 steel (similar to SAE 6150)

CUTTING TOOLS

Cutting Tools include drills, taps, dies, cutters, reamers, end mills, burs, etc. Call for specific requirements

NAILS and STAPLES

SENCO Distributer - Other Lines Available Also. Please Call with Requirements

GENT-L-KLEEN PRODUCTS INC.

Gent-l-Kleen products Inc. manufacturer of America's finest hand cleaners. These products are convenient and economical to use.You can use them with or without a water rinse.

INDUSTRIAL CHEMICALS

MRO Solutions brings over 80 years experience in the MRO Chemical industry to work for you. Products include, thread lockers, antiseize, lubricants, degreasers, etc.